EPDM Shaft Rotary V Ring Seal for Grease & Oil Industry
Basic Info
Model No.: AS, JIS, BS, DIN, Metric and customized
Product Description
Model NO.: AS, JIS, BS, DIN, Metric and customized Application: Cylinder, Equipment Seal Performance: Wear Standard: Standard, Nonstandard Shape (for Gasket): Ring Gasket Color: Pantone Code Available Workmanship: by Mold Vulcanization Tracebility: ERP and Barcode System Trademark: XLONG Origin: China Material: NBR Type: Rotary Seal Shape: V Ring Style: V Ring Seal Function: Fixed Sealing Hardness: Shore a 60-80 Certificate: Ts16949;SGS;RoHS;Reach;Norsok M-710 Usage: Shaft Seal Specification: standard and nonstandard HS Code: 40169310 EPDM Shaft Rotary V Ring Seal in grease and oil industry
Wholesale v ring with different material
1. Compound from world class suppliers, NBR, EPDM, VITON (FKM), HNBR, Silicone, etc material and PANTONE code available, hardness from 30 to 95 Shore A. Imported compound from 3M, DuPont, Bayer, Daikin and Dow Corning, etc.
2. Metric and customize size available.
3. Strict material traceability in ERP and barcode system.
Features
A V-ring consists of a seal body, a flexible, conical-shaped sealing lip and an integral, resilient "hinge". It is stretched and installed
Directly on the shaft, where it is held in place by the inherent tension of the seal
Body. It rotates with the shaft and seals axially against a stationary counterface.
The counterface can be the end face of a bearing, a washer, stamping, bearing
Housing, or even the metal case of a radial shaft seal.
The flexible sealing lip applies contact pressure against the counterface that is
Relatively low but sufficient enough to maintain the sealing function. The light
Contact pressure even enables the seal to run dry in some low-speed applications resulting in insignificant torque drag or heat build-up. The contact pressure varies with the fitted width.
The flexible lip and hinge provide adequate sealing even in applications with
Considerable end play and shaft misalignment.
As a result of centrifugal force, the contact pressure of the lip decreases as speed increases. This means that friction losses and heat are kept to a minimum, resulting in improved wear resistance and extended service life. The power loss reaches its maximum at a shaft speed of approximately 12 m/s (2 360 ft/min) and is thereafter gradually reduced up to 20 m/s (3 900 ft/min), where it will decrease to zero. The V-ring then serves as a gap-type seal and deflector.
Standard designs
VA, the most common type of V-ring, has a standard cross section and straight back sideface. VA is typically used
To protect bearing arrangements in gearboxes, electric motors and drives.
VS, that has a standard low cross section, tapered back face and wide body,
Providing a firm hold on the shaft. VS is commonly used in agricultural and
Automotive applications.
VL, designed with a very compact axial cross section. VL is commonly used in
Confined spaces to replace labyrinth seals.
Main V-ring functions
V rings are suitable for both grease and oil lubricated applications. For sealing
Grease lubricated bearing arrangements and protecting against contaminants, the
V-ring should be arranged outside the housing cover or housing wall. Dust, water
Spray and other contaminants can be excluded in this position. The V-ring can also act as a grease valve, where used grease or excess new grease
Can escape between the counterface and the sealing lip. The installation of two
Opposing V-rings can be used in applications where lubricant retention and contaminant
Exclusion are of equal importance.
If V-rings are used to retain oil, they should always be located axially on the shaft on
The lubricant side.
V-rings should not be submerged in the application medium. Contact us if you need more details on V Seal. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Rubber、V Ring Seal. If these products fail to match your need, please contact us and we would like to provide relevant information.
Wholesale v ring with different material
1. Compound from world class suppliers, NBR, EPDM, VITON (FKM), HNBR, Silicone, etc material and PANTONE code available, hardness from 30 to 95 Shore A. Imported compound from 3M, DuPont, Bayer, Daikin and Dow Corning, etc.
2. Metric and customize size available.
3. Strict material traceability in ERP and barcode system.
Materials | ||
Materials & Temperature Ranges | Fluid Examples | |
Suitable With | Not Suitable With | |
Nitrile (NBR) -40ºC to 120ºC -40ºF to 248ºF | Petroleum Oils Hydraulic Oils Water | Brake Fluids Ketones Phosphate Esters Strong Acids (H2S) |
Hydrogenated Nitrile (HNBR) -40ºC to 150ºC -40ºF to 302ºF | Petroleum Oils H2S (10%) Water | Polar Solvents Brake Fluids Strong Acids |
Ethylene Propylene(EPDM) -50ºC to 150ºC -58ºF to 302ºF | Brake Fluids Water/ Hot Water Steam | Mineral Oils Ozone at High Temperatures |
Fluoroelastomer (FKM) -20ºC to 200ºC -4ºF to 392ºF | Petroleum Oils Silicone Oils Gasoline | Brake Fluids Ammonia Gas Steam |
Perfluoroelastomer (FFKM) -20ºC to 320ºC -4ºF to 608ºF | Most Media | Liquid Sodium & Potassium Fluorinated Solvents & Refrigerants |
Silicone (VMQ) -70ºC to 220ºC -94ºF to 428ºF | Vegetable Oil Water Ozone | Acids &Alkalis Hot Water & Steam (>120ºC) |
Neoprene (CR) -40ºC to 120ºC -40ºF to 248ºF | Ammonia Refrigerants Ozone | Aromatic Hydrocarbons Polar Solvents |
PTFE -200ºC to 280ºC -148ºF to 536ºF | Most Media | Fluorine Molten Alkali Metals Strong Oxidizing Agents |
Polyurethane (PU) -40ºC to 90ºC -40ºF to 194ºF | Most Petroleum Oils | Brake Fluids Hot Water Steam |
PEEK -70ºC to 260ºC -94ºF to 500ºF | Most Media | Hydrochloric, Nitric & Sulfuric Acids |
A V-ring consists of a seal body, a flexible, conical-shaped sealing lip and an integral, resilient "hinge". It is stretched and installed
Directly on the shaft, where it is held in place by the inherent tension of the seal
Body. It rotates with the shaft and seals axially against a stationary counterface.
The counterface can be the end face of a bearing, a washer, stamping, bearing
Housing, or even the metal case of a radial shaft seal.
The flexible sealing lip applies contact pressure against the counterface that is
Relatively low but sufficient enough to maintain the sealing function. The light
Contact pressure even enables the seal to run dry in some low-speed applications resulting in insignificant torque drag or heat build-up. The contact pressure varies with the fitted width.
The flexible lip and hinge provide adequate sealing even in applications with
Considerable end play and shaft misalignment.
As a result of centrifugal force, the contact pressure of the lip decreases as speed increases. This means that friction losses and heat are kept to a minimum, resulting in improved wear resistance and extended service life. The power loss reaches its maximum at a shaft speed of approximately 12 m/s (2 360 ft/min) and is thereafter gradually reduced up to 20 m/s (3 900 ft/min), where it will decrease to zero. The V-ring then serves as a gap-type seal and deflector.
Standard designs
VA, the most common type of V-ring, has a standard cross section and straight back sideface. VA is typically used
To protect bearing arrangements in gearboxes, electric motors and drives.
VS, that has a standard low cross section, tapered back face and wide body,
Providing a firm hold on the shaft. VS is commonly used in agricultural and
Automotive applications.
VL, designed with a very compact axial cross section. VL is commonly used in
Confined spaces to replace labyrinth seals.
Main V-ring functions
V rings are suitable for both grease and oil lubricated applications. For sealing
Grease lubricated bearing arrangements and protecting against contaminants, the
V-ring should be arranged outside the housing cover or housing wall. Dust, water
Spray and other contaminants can be excluded in this position. The V-ring can also act as a grease valve, where used grease or excess new grease
Can escape between the counterface and the sealing lip. The installation of two
Opposing V-rings can be used in applications where lubricant retention and contaminant
Exclusion are of equal importance.
If V-rings are used to retain oil, they should always be located axially on the shaft on
The lubricant side.
V-rings should not be submerged in the application medium. Contact us if you need more details on V Seal. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Rubber、V Ring Seal. If these products fail to match your need, please contact us and we would like to provide relevant information.
Product Categories : V Ring
Premium Related Products
Other Products
Hot Products
Customize Rubber Seal for Dynamic SealTs16949 High Quality with Factory Price Blue Hydraulic SealApproved Norsok M-710 Certificate FKM Aed O Ring for ValveBlack As568 Standard Quad Ring for Hydraulic CylinderChina Factory Supply Top Quality Rubber Oil SealRubber Viton Ring Va/Vs Seal for PumpFlat Gasket / Back-up Ring with FDA Confirmed for SealingFlexible Black NBR 70 Rubber Cord/Strip for SealingPTFE Spring Energized Seal for -196 Working ConditionSolid NBR Rubber Ball for Brake SystemFEP Encapsulated Black Viton O-Ring for SealingRubber Seals Rubber Gasket and Rubber PartsVarious Sizes of Rubber Oring Rubber Ring Spare PartsHigh Performance Industry Rubber Products and Rubber PartsFDA Silicone Rubber Seal Rubber Parts Rubber OringUL Approved NBR Custom Molded Rubber Products